Skip Navigation
Send E-MailCompany InformationCall us at 212-555-1212

N-SERIES SCALING HAMMERS & NEEDLE SCALING HAMMERS

Features:

  • Quick realease needle attachment converts needle scaler to chisel scaler in seconds.
  • The tool nose that holds the chisel can be replaced when worn out.
  • Front exhaust keeps work area clean.
  • Three-position "J" slot on needle scalers allow compensation for needle wear.

 
N-2R Needle Scaler (TOP) (your choice of 5" or 7" needles) needle attachment can be removed to instantly convert to a standard chisel scaler.
N-3R Chisel scaler (Middle)shown with 7" narrow chisel. (can easily be converted to a needle scaler in seconds.
N-1R Push throttle type scaler. (Bottom) (Shown with angled chisel) can easily be converted to a needle scaler in seconds with an optional needle attachment.
N-3RP Pistol scaler can also be converted to a needle scaling hammer with the addition of a needle scaler attachment.
All the above scaling hammers use a 1/2" Square shank type chisel. (See the red chart below for full chisel information)
Model Throttle Type Scaler Type Blows Per Minute Bore and Stroke Weight Length Shank Type Inlet Size Hose Size Working Air Consumption Parts Print
N-1R Push Type Scaler 5000 1" dia. X 1.125" 4 lbs. 5 oz.
1.9 kg		 12"
304mm		 1/2" Sq. 1/4" 3/8" 20 cfm Parts Print
N-2R Lever Needle Scaler 6.1 lbs
2.7 kg		 15"
381mm		 3/8" Parts Print
N-2RP Offset (Pistol) Pistol Needle Scaler 6.2 lbs
2.8 kg.		 1/4" Parts Print
N-3R Lever Scaler 4 lbs. 5 oz.
1.9 kg		 10 1/4"
260mm		 3/8" Parts Print
N3-RP Offset (Pistol) Scaler 4 lbs. 10 oz.
2 kg		 1/4" Parts Print
N-4R Push Type Needle Scaler 6.1 lbs.
2.7 kg		 16 3/4"
425mm		 1/4" Parts Print

Recommended working air pressure: 90 p.s.i.
* All the above scaling hammers use a 1/2" Square shank type chisel.

CHISELS FOR N-3 SERIES SCALING HAMMERS - 1/2" SHANK TYPE

Part No. Description Cutting Edge Width   Overall Length Shank Type 1/2" Square
839050 C-200-7 Angle Chisel 1 3/8"
7 1/4"

1/2" Square Shank
839051 D-200-7 1/2 Narrow Chisel 3/4"
7 1/2"
839299 C-200-12 Angle Chisel 1 3/8"
12"
839334 C-200-18 Angle Chisel 1 3/8"
18"
839335 D-200-18 Narrow Chisel 3/4"
18"
839341 D-200-12 Narrow Chisel 3/4"
12"
839467 B-100-7 Wide Chisel 1 3/8"
7"
839469 B-200-12 Wide Chisel 1 3/8"
12"
839470 2" Wide Scraper 2"
7 1/2"
839471 3" Wide Scraper 3"
7 1/2"

 

 

F-1000 SERIES HEAVY DUTY SCALING HAMMERS

Features:

  • Extreme hard-hitting action - tool can be used as a compact chipping hammer.
  • Quick change 4-ball type chisel retainer.
  • Possible four-way positioning of chisel.
  • Choice of lever, push, or offset type throttle.
F-1000-L Heavy duty scaler with lever type handle. Super hard hitting.
F-1000-P Push Type Heavy duty scaler.
F-1000-BW Pistol type heavy duty scaler.
Model Throttle Type Bore & Stroke Net Weight Length Shank Type Inlet Size Working Air Consumption Parts Print
F-1000-L Lever .937" x 2" 4 3/4 lbs. - 2.1kg 11"-279mm 4 Ball 3/8" N.P.T. 20 cfm  
F-1000-P Push 4 1/2 lbs. - 2 kg 12 1/2" - 318mm 1/4" N.P.T  
F-1000-BW Offset 4 3/4 lbs.-2.1 kg 10 1/2" - 267mm  

Recommended working air pressure: 90 p.s.i
Standard Equipment: (1) screen bushing.

CHISELS FOR F-1000 SERIES HAMMERS - 4 BALL SHANK TYPE

Part No. Description Cutting Edge   Overall Length Shank Type
718480 Angle
1 3/8"
7"

4 Ball Shank
718481 Wide
1 3/8"
7"
718481-12 Wide
1 3/8"
12"
718482 Narrow
3/4"
7"
718483 Scraper
2"
7"
718484 Narrow
3/4"
12"

 

 

N-16 SERIES LIGHT DUTY CHIPPING HAMMERS

Features:

  • Hard-hitting action for fast chipping and peening.
  • Adjustable 360 degree side exhaust deflector.
  • Heavy-duty spring type chisel retainer.
  • Available with either a hex, round, or taper tool nose.
N-16 chipping hammer is lightweight and easy to maneuver.
Model Tool Nose Type Shank Size Blows Per Minute Bore & Stroke Weight Length Inlet Size Hose Size Working Air Consumption Parts Print
N-16X Hex .371" Hex 5200 .625" x 1.437" 3 lbs., 3 oz.
1.5 kg		 8"
203mm		 1/4" NPT 3/8" 20 cfm Parts Print
N-16R Round .401" Round Parts Print
N-16T Taper .401 Parker Taper Parts Print

Recommended working air pressure: 90 p.s.i.
Standard Equipment: (1) Beehive round retainer, (1) screen bushing.

CHISELS FOR N-16 SERIES CHIPPING HAMMERS

Part No. Description Cutting Edge Width Overall Length Shank Type
595001 Narrow
1/2"
7"
 .401 Round Shank
595003 Narrow
12"
595004 Narrow
18"
596009 Narrow
7"
 .371 Hex Shank
596010 Narrow
12"
596011 Narrow
18"

 

 

HT-4B SERIES HEAVY DUTY CHIPPING HAMMERS

Features:

  • Ergonomically designed handle located operator hand-in-line with the chisel for maximum operator comfort.
  • A forged steel or lightweight aluminum handle is available for the ultimate in versatility
  • 4-Bolt design provides ease of maintenance.
  • Choice of round tool nose for .680" round shank chisels or hex tool nose for .580" hexagon shank chisels.
HT-4B30 Heavy Duty Chipping Hammer. (You specify either hex or round tool nose to accomodate your particular chisel type when ordering)
Model Blows per Minute Bore and Stroke Overall Length Net Weight with Forged Steel Handle Net Weigth with Aluminum Handle Air Inlet Working Air Consumption Parts Print
HT-4B20 2400 1 1/8" x 2", 28.5mm x 50.8mm 14"
356mm		 13.5 lbs
6.1 kg		 9.5 lbs 3/8" N.P.T. 25 cfm  
HT-4B30 1920 1 1/8" x 3", 28.5mm x 76.2 mm 16" 406mm 14.5 lbs
6.5 kg		 10.5 lbs  
HT-4B40 1500 1 1/8" x 4", 28.5mm x 101.6mm 17"
432mm		 15.5 lbs
7.0 kg		 11.5 lbs  

PLEASE NOTE WHEN ORDERING:

* For a tool with an aluminum handle, add an "A" to end of model number.
* For a tool with a hex tool nose, add an "X" to end of model number
* For a tool with a round tool nose, add an "R" to end of model number.

CHISELS FOR HT SERIES CHIPPING HAMMERS .580 HEX & .680 ROUND SHANK TYPE OVAL COLLAR

Part No. Description Cutting Edge Width   Overall Length Shank Type
839008 Narrow
1"
9"

.580 Hex Shank
839009 Narrow
1"
12"
839010 Narrow
1"
18"
839016 Wide
2"
12"
839018 Moil Point
-
9"
839014 Narrow
1"
9"

.680 Round Shank
839017 Wide
2"
9"
839023 Moil Point
-
9"
839045 Narrow
1"
18"
839047 Wide
2"
12"
839083 Narrow
1"
12"

 

CHIPPING HAMMER RETAINERS

Part No. Size Fits Tool Model Pictured
P-107243 For Oval Collar Type Chisels HT-20, HT-30, HT-40 or Chicago Pneumatic 4123 Series Chippers.
2500-12-525
(6872122)		 HT-4B Series or Sullair Chippers

 

SWIVEL HOSE CONNECTOR

Part No. Description Pictures
1080 For all chipping hammers with 7/8-24 I.D. inlet thread. Use with all HT Series Chipping Hammers.

 

 

HT SERIES HEAVY DUTY CHIPPING HAMMERS

Features:

  • Rugged forged Steel handle.
  • Simplate valve assembly provides fine control of throttle and trouble free operation.
  • Choice of round tool nose for .680" round shank chisels or hex tool nose for .580" hexagon shank chisels.
Model Blows per Minute Bore and Stroke Overall Length Net Weight Air Inlet Working Air Consumption Parts Print
HT-20 2400 1 1/8" x 2", 28.5mm x 50.8mm 14"
356mm		 13.5 lbs
6.1 kg		 3/8" N.P.T. 25 cfm  
HT-30 1920 1 1/8" x 3", 28.5mm x 76.2 mm 16" 406mm 14.5 lbs
6.5 kg
HT-40 1500 1 1/8" x 4", 28.5mm x 101.6mm 17"
432mm		 15.5 lbs
7.0 kg
  * For a tool with a hex tool nose, add an "X" to end of model number.
* For a tool with a round tool nose, add an "R" to end of model number.

CHISELS FOR HT SERIES CHIPPING HAMMERS .580 HEX & .680 ROUND SHANK TYPE OVAL COLLAR

Part No. Description Cutting Edge Width   Overall Length Shank Type
839008 Narrow
1"
9"

.580 Hex Shank
839009 Narrow
1"
12"
839010 Narrow
1"
18"
839016 Wide
2"
12"
839018 Moil Point
-
9"
839014 Narrow
1"
9"

.680 Round Shank
839017 Wide
2"
9"
839023 Moil Point
-
9"
839045 Narrow
1"
18"
839047 Wide
2"
12"
839083 Narrow
1"
12"

 

CHIPPING HAMMER RETAINERS

Part No. Size Fits Tool Model Pictured
P-107243 For Oval Collar Type Chisels HT-20, HT-30, HT-40 or Chicago Pneumatic 4123 Series Chippers.
2500-12-525
(6872122)		 HT-4B Series or Sullair Chippers

 

SWIVEL HOSE CONNECTOR

Part No. Description Pictures
1080 For all chipping hammers with 7/8-24 I.D. inlet thread. Use with all HT Series Chipping Hammers.